6.9

Very cool will look for 1 when I get a box

pretty cool gadget, must look into this for myself

SHEEEIT! the price is ridiculous. here is the unit I am looking at using. http://www.ofgear.dk/

And a little movie of one being used. https://youtu.be/qYhNcl7JfsQ

https://automatictransmission.com.au/shop/compushift-chrysler-nag1-automatic-transmission-controller/

Yes I have Intention to go down that path and change rear gearing as Overdrive gearbox will make that viable. Stand alone control boxes are more to do with Chrysler using this box and calling it NAG1.And car builders fitting Hellcat engines to older cars.

Oh man ,I hope you are OK now!. My own 6.9 project has stalled for a few reasons too but this year i hope to get a few of these customers cars squared away and begin to finish the whole thing. I am toying in mind with making a 722.6 trans work behind an m100 .I like how they shift and there are now stand alone ECM's for them.It's what I think is missing from the cars,the ability to have an overdrive. I have all the ducks lined up,I just have to get organised.

The car has not gone anywhere and hopefully work will recomence later this year . I was involved in a fairly large motor vehicle accident. Was run into by a drunk driver.

Received billet throttle bodies yesterday size next to standard 6.9 throttle body 65mm 649CFM V 85mm 1322CFM

Will know when dyno is done also fitting FrankenCIS WUR

Hi MOTEC

I've been following your story on Topklasse but plz'd to see you have kept this forum appraised of your recent endeavours. This reborn throttle body is a crafty bit of innovative thinking. you deserve a medal for persistence. You've taken a damn good idea and applied 21st century technology to execute it. [^] Hoping this delivers for you. I might even buy one myself!

Cheers

Throttle bodies made will have them by the end off the week.

Throttle bodies

Apparently this is my Dkubus FrankenCIS WUR ready for shipping. My throttle bodies will be finished by end of next week as well. I have been told.

Sorry picture take 2

First block of Billet has been turned on the Lathe this is the result so far.

And so it begins. Billet blocks cut for fitting onto CNC Lathe to be made into 85mm throttle bodies.

I tweaked the post that shows the injectors to include a line break between the URL and pretty picture. It fits on my computer screen now.

HTH -CTH

Still thinking about these as I have 16x8 inch real Penta rims. But these are Billet and any size I want thinking 18x8 & 18x9 or 10 just working out if there is room in money I have put away for engine work and paint job this year.

And also upgraded torque converter. Dkubus now offering 2 options in torque converters first is our "rally/road/sporty" converter for 400+hp and then also a new "race/track" model for less rotating mass and bigger bearings plus a higher launch RPM built strong for 750+hp!!
We race, and develop so that you can buy parts that work.

As well as the throttle body. I have confirmed order of FrankenCIS tuneable WUR with Dkubus today will have in 2 weeks. FrankenCIS system by Dkubus, component list:
Wideband O2 with The latest Bosch 4.9 sensor, 3 bar map sensor for boost or n/a setup, fast response Intake air temp sensor, engine temp sensor, full braided loom, FrankenCIS e-WUR unit assembled with digital 100 psi sensor, pressure damper, control injector & temp sensor, Microsquirt ECU with sealed case and pre loaded with firmware and base tune to suit start-up. Dedicated ignition loom, option loom, fuel loom. Simple hook up / plug in. Installation manual.